VELCRO® Brand Adhesive 19 Hook Fastener (2-pcs)

$12.00 USD
Shipping calculated at checkout.

Includes 2x VELCRO® Brand Adhesive 19 hook fastener. Use as a spare or replacement adhesive for Hazard 4® Jeep Molded Storage Headliners.

VELCRO® 2-pc set: 12" L x 4" W (30.5 x 10.2 cm) and 16" L x 4" W (40.6 x 10.2 cm).

Pressure Sensitive Adhesive Hook Fastener Application Instruction:

1. Thoroughly clean the surface of the adhered substrate, remove oil, water, and dust, etc. and wait for it to dry completely. All cleaning agents should be tested prior to using, to be sure the cleaning agent will not have adverse effects on the substrate. (Citrus cleaners are not recommended.) In automotive hardtop interior application, Isopropyl alcohol (rubbing alcohol) may be a sufficient cleaning agent.

2. Peel the release liner from fastener tape and press firmly back and forth for at least 2 minutes into place. Note: Apply adhesive only indoors free of dirt and dust at room temperature 15°C-26°C/59°F-79°F and relative humidity 40%-60% (the lower the humidity, the better the bond). Applying adhesive under 10°C/50°F is not recommended as it may not bond properly. If adhesive must be applied at lower than 10°C/50°F, warm the substrate and the tape to elevate temperature prior to applying.

3. Curing Time: allow 24-30 hours to achieve full bonding strength. Do not load before full curing time.

Operating Temperature Range: -40°C to 85°C/-40°F-185°F

Note: Pressure sensitive adhesive products are not permanent bonds, and performance may vary and diminish depending on the environment and usage.

Unlock Exclusive Gifts.

Powered by Salepify App

Details

_ Includes 2x VELCRO® Brand Adhesive 19 hook fastener only.

Specs & Dims

VELCRO® 2-pc set: 12" L x 4" W (30.5 x 10.2 cm) and 16" L x 4" W (40.6 x 10.2 cm).

Instruction/Care
VELCRO® Brand Adhesive 19 Hook Fastener

Pressure Sensitive Adhesive Hook Fastener Application Instruction:

1. Thoroughly clean the surface of the adhered substrate, remove oil, water, and dust, etc. and wait for it to dry completely. All cleaning agents should be tested prior to using, to be sure the cleaning agent will not have adverse effects on the substrate. (Citrus cleaners are not recommended.) In automotive hardtop interior application, Isopropyl alcohol (rubbing alcohol) may be a sufficient cleaning agent.

2. Peel the release liner from fastener tape and press firmly back and forth for at least 2 minutes into place. Note: Apply adhesive only indoors free of dirt and dust at room temperature 15°C-26°C/59°F-79°F and relative humidity 40%-60% (the lower the humidity, the better the bond). Applying adhesive under 10°C/50°F is not recommended as it may not bond properly. If adhesive must be applied at lower than 10°C/50°F, warm the substrate and the tape to elevate temperature prior to applying.

3. Curing Time: allow 24-30 hours to achieve full bonding strength. Do not load before full curing time.

Operating Temperature Range: -40°C to 85°C/-40°F-185°F

Note: Pressure sensitive adhesive products are not permanent bonds, and performance may vary and diminish depending on the environment and usage.

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
R
Ronald Barnes
Quick service.

Replaced the Velcro strips attached to the freedom panels on my JT due to my improper installation. Received them quickly and installed them properly. Happy with the service and product.